Methods of fixing to a shaft

There are many solutions for attaching a gear to a shaft. Here are a few ideas which should help you in your installation:
Prilog sa a vijak za pričvršćivanje Attachment with a Ključ i kopča
   
Prilog sa a Igla Prilog sa a Locking assy.
Prilog sa a Prsten za zaključavanje Prilog sa a Samopodmazujuća čahura
   
PRINCIPALI

Assembly with a fixing
vijak je vrlo jednostavan. Jednostavno
treba biti rupa s navojem
obrađen u glavčinu i
obrada zaravnjenog područja
na vratilu. Snage jesu
koncentriran na ivicama
the cup headed screws (GM and SM)


PREDNOSTI

This type of fixing improves adherance
and stops all displacement.
Prenosni moment je ograničen sa
this kind of mounting
Stoga se preporučuje za fiksiranje
of low module gear wheels.
The threaded hole is standard on all HPC pulleys.

PRINCIPAL

The use of a key attaches the gear to the shaft by stopping rotation between the two. A groove, or keyway must be machined into the bore and shaft. For manufacturing practicalities, the groove cut into the bore must traverse the whole width of the gear.

Paralelni ključ - je pravougaoni
piece of metal, embedded half and
pola u osovinu i glavčinu. Mašinska obrada
žlijeba u vratilu je završeno
with the aid of a two bladed cutting tool.
A keyway of this type is excellent for the transmission of high torque levels.

 

->  
Disk (or half moon) keys are used for the transmission of weaker couples. The machining of the keyway into the shaft is very easily done using a three bladed cutter.
 ->  
A keyway does not stop axial movement of the system. Therefore it must be combined with another locking system, such as a thread and boltili jednostavnije, sigurnosnim kopčama.
  • Prilog sa stezaljkama
PRINCIPAL

Circlips, stop axial movement between two componants.
There are two types of circlips, one for shaft mounting and one for inside the bore.

Upotreba

The utilisation of these elements needs a groove to be cut into either the bore or the shaft. They are then fitted axialy, from one end of the shaft or bore with the aid of a specialised tool. pažnja, a minimum (or maximum) clearance diameter is needed for the installation.

The use of these componants is often associated with a KLJUČ in the assembly of pulleys or spur gears.
  • Montaža sa iglama  
PRINCIPAL

The cotter pin has the effect of immobilising one componant with respect to another, of assuring an accurate relative positioning of the two pieces, or of transmitting a movement. It can also play a safety role by shearing away u slučaju nasilne nadoplate.

Upotreba

Essentially, the pin is subject to shearing, and should therefore be used in cases where there is relatively little torque involved. It's usage is not recommended where frequent removal is necessary. The piercing of the pinholes is generally done after assembling the componants in order to assure perfec t alignment.

The use of a cylindrical cotter pin needs the precise machining of a hole through the shaft and gear. A rough hole is good enough because the pins will adjust by deforming in their seating.
This property gives them a very good resistance to vibration.
This type of assembly is excellent for small toothed wheels or pulleys, or gears with low modules.
  • Instalacija sa sklopom za zaključavanje.
PRINCIPAL

By tightening the screws, the user deforms a conical ring, and causes a strong force between the shaft and bore. The liasion obtained is complete and rigid (i.e. backlash free) , and easily removed.

 -> 
PREDNOSTI

By avoiding the manufacturing accidents which can be caused whilst cutting keyways etc?This system actually increases the sectional strength of the shaft and decreases both the concentration of stress points and the phenomenon of metal fatigue cracking.

For equal diameters, the transmissible couple with this method is much higher. Work to be done on the shaft and bore is limited to insuring an H8/h8 tolerance and a surface finish of at least Ra=1,6mm for self-centering assemblies (RT25 and RTL450).

A guide should be envisaged for the other assemblies. These locking assemblies are recommended for all types of toothed wheels, and especially for pulleys, sprockets and gears with large pitches or important modules. 

  • Pričvršćivanje sigurnosnim prstenom
Attachment by locking ring is a fast and efficient method of attaching all types of toothed wheels. Two solutions exist, locking with half a locking ring (type CT), or locking with the aid of a full collar (CC).
THE USE OF A HALF-ROUND RING (CT)

This first solution involves the machining and removal of half of the gear hub and the piercing of two threaded holes in the rest of the hub.

USING A LOCKING RING (CC)

The other solution involves trimming the hub and the machining of two channels - as shown in the diagram
.

In both cases, the result is a completely rigid joint, which is perfectly suited to the transmission of high levels of torque.

  • Montaža samopodmazujućom čahrom.
PRINCIPAL

This very simple system provides a reliable, simple and efficient rotational guidance. It manages to limit friction between the shaft and bore with the aid of two self lubricating bushes (type QAF or QAG), and at the same time, stopping axial movement of the rotating object.

The locking elements the most practical are locking rings (CT or CJ). They have no requirement for special machining and can be positioned at any point on a shaft, allowing for adjustments to the position of the pivot point.

Brava CJ:

Stezna ogrlica CT  :

 
The use of self-lubricating Ollite QAG or QFM bushes imposes a maximum tolerance of f7 on the shaft and H8 on the bore (see ISO 2795 and 2796).